+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Hyundai: Fumoto drain valve

  1. #1
    KR
    Guest

    Fumoto drain valve

    I have always done my own oil changes, changing the washer and/or
    drain bolt as needed.

    I would like opionions on the Fumoto drain valves: problems,
    experience, clearance problems, etc.

    I am trying to decide if installing one of these on my personal car is
    worth it.

    P.S. I have severe back problems and pain so anything making my
    maintenance work easier is very welcome.

  2. #2
    Jason
    Guest

    Re: Fumoto drain valve

    On Sun, 22 Aug 2004 13:14:40 GMT, KR <com> wrote:
     

    I don't have anything to say about the drain valve but your health
    should come first. Saving $10 isn't worth back problems.

  3. #3
    Curtis
    Guest

    Re: Fumoto drain valve

    On Sun, 22 Aug 2004 13:14:40 GMT, KR <com> wrote:
     



    Have the valve on both of our cars (01 Audi A4 and 04 Lexus
    RX330)...it works nicely.

    If you order the one with the nipple, make sure your car has plenty of
    clearance.


    -
    --
    com
    Anti-Spam filter in place--
    <delete .remove-this to respond to email>

  4. #4
    KR
    Guest

    Re: Fumoto drain valve


    Thanks for the concern. I am a former mechanic, so in my time I have
    probably changed the oil on 50,000 cars (not including my own) so
    doing this is second nature to me. I would no more let some
    inexperienced worked do this work on my car than I would let some
    inexperienced Doctor operate on me. If most people only knew how easy
    it is and what steps they need to take plus what things to watch out
    for, a lot of people would change their own oil.

    P.S. When I have extreme back pain, I take it to the dealer with my
    own oil (Mobil 1) and filter (Mobil 1) and let them do the labor
    (about $13). I never take it to a JiffyLube or any quick change place.

  5. #5
    Jason
    Guest

    Re: Fumoto drain valve

    On Mon, 23 Aug 2004 12:01:59 GMT, KR <com> wrote:
     

    That's the same thing that I do. I take my car to the dealer and give
    them the 5 quarts of Mobil 1 and they supply the Hyundai filter and
    labor. They charge me about $12.00.

  6. #6
    Brian
    Guest

    Re: Fumoto drain valve

    KR wrote:
     

    Fram makes a drain valve that's smaller, simpler, less expensive and
    easier to find than the Fumoto. It works well.


  7. #7
    KR
    Guest

    Re: Fumoto drain valve

    And the part number is..............?

    On Mon, 23 Aug 2004 13:27:42 GMT, Brian Nystrom
    <net> wrote:
     


  8. #8
    Curtis
    Guest

    Re: Fumoto drain valve

    On Mon, 23 Aug 2004 13:27:42 GMT, Brian Nystrom
    <net> wrote:
     


    I have used both and for my prerference, have found the Fumoto to be
    better.

    --much faster drain time
    --made of better materials

    I will agree there wasn't anything wrong with the Fram, I just prefer
    the Fumoto for the reasons above...and you can order it without even
    leaving your computer chair from http://www.fumotovalve.com

    -
    --
    com
    Anti-Spam filter in place--
    <delete .remove-this to respond to email>

  9. #9
    S25
    Guest

    Re: Fumoto drain valve

    On Sun, 22 Aug 2004 13:14:40 GMT, KR <com> wrote:
     

    I installed a Fumoto (with the nipple) on my Santa Fe and draining
    the oil is VERY simple. No problems in my experience. Some folks
    might not like the used oil handling but I consider it part of owning
    a car (rotate my own tires, too).

    The Fumoto was better for me - install one part and forget. The
    Fram has a couple of pieces and I'd probably misplace the loose
    Fram item.

    Plenty of clearance on my Santa Fe. You don't mention on what
    vehicle you would install the drain valve.

    S25

  10. #10
    Brian
    Guest

    Re: Fumoto drain valve



    S25 wrote:
     

    Let's clarify this, shall we. There is one part that installs on the
    car. It comes with a cap to keep the valve clean and prevent any
    possibility of leakage. To drain the oil, all you do is unscrew the cap
    and screw on the drain tube assembly.

    As for the material mentioned in another post, the Fram valve is made of
    brass. How is that in any way inferior to any other material for this
    application?



 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Search Engine Friendly URLs by vBSEO 3.6.0

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48